"Minke" is the ultimate self-contained self-reliant world cruiser. With a brand-new electric drive engine (well over $30,000 in value just for the engine and batteries) and all systems built, replaced or modified by her engineer owner, she is the boat for you if you want to cruise exotic places in safety and comfort and self-sufficiency!
Don't miss the opportunity to own this incredible steel sailing ship! A boat like this comes along once in a lifetime, and it is the last boat you will ever need. NEW generator. New refrigeration. New batteries. Extensive Both 110 and 220 (European) compatible electrical circuits for world cruising. Dual helm stations in pilothouse and in cockpit. Not a spot of rust, beautifully maintained. Reinforced steel plating. Extensive work done over last year!
The Story Behind Minke's Repower
From the owners:
Back in July 2016, while motoring down the Richelieu River, our Perkins 4-108 diesel engine completely failed and was not able to be rebuilt. My husband, Dan, and I were devastated but after many hours of researching possible solutions we decided to go the electric/hybrid route. The electric/hybrid system supports our desire to reduce our carbon footprint and even if we wanted to install a new diesel replacement we couldn’t since the marina we were stuck at didn’t have the capability to install the engine into our boat.
With the decision made we then furiously began researching companies that could re-power s/v Minke with an electric/hybrid system. Luckily, we found a person that had the drive and the will to help us reach our goal. Nancy Frainetti, the owner of The Electric Marina and a dealer for Electric Yacht, began sending emails with the possibilities of what we could do to get Minke up and running again. After a flurry of emails back and forth with Nancy relaying calculations formulated by Scott McMillan, and Mike Gunning at Electric Yacht, we decided to go forward with the QuietTorque 20.0 kW, 48 Volt package powered by four Torqeedo Power 26-104 batteries and two 1700W Torqeedo chargers. The calculations were based on the total displacement of our boat (24000 lbs), the waterline beam (10'6"), length of waterline (29') and an estimation of RPM at different knot speeds when we were running with our Perkins engine.
Setting aside the stress of what we were going to replace the old diesel with, we began tearing the old engine apart piece by piece. Most of the electric/hybrid installation videos that you can watch online show the old engine being whisked away easily from the hull with the use of a crane. Unfortunately, that was not a possibility at our current location so the engine had to be downsized. Most of the smaller pieces were easily removed except for the engine block and transmission which each weighed about 150 lbs after being completely disassembled. With the use of our Canadian Tire chain fall hoist, we were able to pull it out of the engine compartment, then with a lot of heavy lifting up the stairs, we carefully slid them out the hatch to the edge of the boat and down a plank into a cart. It was a great feeling once the engine and transmission were removed and thanks to Trans Atlantic Diesels we were able to sell our parts for a few dollars.
The next steps to follow included cleaning the engine compartment with degreaser and repainting it. Metal mounts for the new electric motor were fabricated as well as platforms to mount the batteries. The large wire connections were cut to length terminals were installed, and the Electric Yacht Display and two throttles were mounted. Once the batteries were installed and secured they were connected into a series parallel bank in order to produce 48 Volts with 208 amp hours. Connections were made from the power relays to the batteries, chargers and fuses were installed and power from the batteries was connected to the motor. Since we needed to produce electricity while we are motoring down the river we bought a 5.5 kW gas generator to use on the deck powering us until got to the Canadian/US border at Rouses Point NY.
After a little over a month of constant work, Dan and I pushed the silver Torqeedo battery button, waited for the red light to blink and then we turned the key. The throttle lever was slid forward and the propeller shaft began to rotate. After such a long wait the cobwebs between Minke and the dock were ripped away, we had power once again and the sweet hum of the motor was music to our ears.
After finally making it across the border Minke was hauled out in NY at Gaines Marina. During the two weeks on the hard we installed an Ultra Compact Marine 5.5 kW Next-Gen diesel generator, change out our propeller to a new Michigan Wheel DJX 18inch diameter 15 pitch and repainted Minke's underside so she was ready for the push down to FL. We were under way heading South through Lake Champlain to the Hudson river. We noticed Minke moves so much better than with her old Cambel Sailor prop 18 inch by 11 inch pitch. We can reach hull speed and maneuvering at slow speed has improved so much! One of my favorite improvements is that the Electric drive makes close quarters handling so much simpler. We have even been able to back into docks which was not possible before.With the old Perkins diesel we had a separate throttle and transmission lever for forward and reverse. I always felt like I needed 3 arms to operated the levers and wheel when coming into a dock. With the new system we can easily transition between forward and reverse with the use of one simple lever plus we do not have to worry about harming a transmission if we need to quickly put the throttle in reverse.
Motoring south through Lake Champlain we decided to collect data on the output of the electric motor and we noticed that with the new prop the motor was not reaching the recommended RPM’s and amp draw that would operate most efficiently. We contacted Scott and Nancy and without hesitation, they shipped a set of pulleys and belts to better match the motors to the Prop. When we arrived at Catskill, NY to re-step our mast, the pulleys and belts were waiting for us. Switching the pulleys and belts was simple and only took about and hour. With our mast up and the QT20 motor now at a better ratio it was time to get moving south one again.
We had read that our propeller would be able to regenerate power while we were sailing but since we are a slow boat I was not expecting too much to come from this. I think that the choice of our lithium batteries and their voltage has made it less likely that we will get much regeneration from the propeller unless the bank voltage is low. While sailing through the Chesapeake Bay we were able to see regeneration from the Propeller. Our Torqueedo battery bank when fully charged has a voltage of 58.2V. I noticed regeneration from the prop when the batteries were about 52V. When sailing at around 5 Knts the state of charge meter displays the motor turning between 500 and 550 rpm. Input amps to the batteries was around 1.5A but we did see up to 7 amps for a short period when we had a few gusts that pushed us up above 6 Knts but most of the time it is in the 1.5Amp range (I have included a chart with some data on the speed and amp draw).
After 3 months of daily use we have been extremely satisfied with our purchase. We were not planning to re-power but the benefits from our electric propulsion system have been numerous. I would also like to state that the customer service that we have received has exceeded our expectations and we are so happy to have found such a great crew to support us through this re-powering process.
Below are some photos that were taken and our journey on Minke can be followed at:
Minke's Equipment List
20K.W. Electric Propulsion by Electric Yacht
Wow! This is the best equipped steel cruising vessel that I have ever seen. If you are an adventurer who wants to sail around the world with peace-of-mind and self-sufficiency, this is the boat for you. The owners have spared no expense in outfitting her. Their cruising plans changed, and it is up to you to pick up where they left off.
"Minke" was professionally built in Canada at Shipham Boat Works in 1995 and was a freshwater boat for her entire life up until 2016. She is a multi-chine mild steel boat with reinforced steel stringers, an impressive grid system, and all the reinforcement one could possibly want in her construction. There are no bare steel surfaces--all surfaces have been coated with top-quality epoxy finishes. Her hull shines, and her bottom paint and zincs are all brand new.
Pre-purchase survey from 2016 available on request, but this was completed before the -current owners completely refitted her.
Currently hauled in Indiantown, FL. Call me! 305-807-4096!